Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Light Weight Self Compacting Concrete With Light Expanded Clay Aggregate (LECA)1751846634610.21608/erjm.2017.66346ENKhaled M.HeizaProfessor, Civil Engineering Department, Faculty of Engineering, Menoufia University, EgyptFatma M.EidLecturer, Civil Engineering Department, Faculty of Engineering, Menoufia University, EgyptTahaMasoudCivil engineer at ministry of housing, EgyptJournal Article20191225Lightweight concretes have been successfully applied in the building constructions for decades because of their favourable material properties, especially their low specific weight in connection with a high strength, a high capacity of thermal insulation and a high durability. The development leading to light weight self compacting concrete(LWSCC) represents an important innovative step in the recent years. This concrete combines the favourable properties of a lightweight concrete with those of a self compacting concrete. Research work is aimed on development of (LWSCC) with the use of light aggregates ‖Light expand clay aggregate (LECA)‖. In this investigation, first by specific gravity factor method, Twenty different mixes design of (LWSCC) were casted and tested to find out the values of slump flow, G-ring , V-funnel and 28 day compressive strength. Based on the results obtained, the best mix design was selected for further investigation. For the selected mix we study the effect of changing the reinforcement ratio on reinforced two way slabs when the dimensions were kept constant.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Structural Performance of Space Trusses under Fire1851966634710.21608/erjm.2017.66347ENAmr M.IbrahimPh.D. Student, Civil Engineering Department, Faculty of Engineering, Minoufia University, Gamal Abdul-
Nasser Street, Minoufia, EgyptAhmed A.ElshafeyLecturer, Civil Engineering Department, Faculty of Engineering, Minoufia University, Gamal Abdul-
Nasser Street, Minoufia, EgyptBoshra A.EltalyAssociate Professor, Civil Engineering Department, Faculty of Engineering, Minoufia University, Gamal
Abdul-Nasser Street, Minoufia, EgyptKamel S.KandilProfessor, Civil Engineering Department, Faculty of Engineering, Minoufia University, Gamal Abdul-
Nasser Street, Minoufia, EgyptJournal Article20191225An experimental program was designed in the current work to capture the structural behavior of two different space trusses under static loads and under increasing the temperature at the truss nodes up to failure. The results of the two space trusses tested include the central deflection of the truss and the axial forces in truss members under the applied loads and temperature. Also analytical studies based on finite element method for the two tested trusses are introduced in this paper. A comparison between experimental work and analytical study is presented and discussed. The finite element simulation gives good agreement with the experimental results. Also the results of the current work indicate that increasing the temperature causes a local failure due to fusion of the node at which the temperature was applied.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Experimental and Numerical Behaviour of CFST Columns with Longitudinal Stiffeners1972096634810.21608/erjm.2017.66348ENMohamedIbrahimTeaching Assistant, Civil Engineering Department, Higher Institute of Engineering and
Technology in Kafr El-sheikhMaherElabdLecturer, Civil Engineering Department, Faculty of Engineering, Menoufia UniversityKamelKandeelProfessor of Steel Structures and Bridges, Civil Engineering Department, Faculty of
Engineering, Menoufia University.Journal Article20191225The use of Concrete Filled Steel Tube CFST is increasingly implemented in the design of modern buildings for their high loading capacity and ductility compared to reinforced concrete or hollow steel columns if worked separately. Changes to structural usage may result in increasing the loads on building columns. This paper presents the experimental test results and non-linear finite element modelling of experimental test program carried on Concrete Filled Steel Tube CFST columns with longitudinal stiffeners as a proposed solution to increase the CFST capacity. The nonlinear analysis has been performed using ABAQUS and the finite element model is validated and verified against the test results conducted in this study. The study extends to include different parameters affecting the design of CFST columns by implementing the validated numerical model. The parameters include the stiffener shape, the number of stiffeners per specimen and the diameter to the tube thickness (D/t) ratio. Behaviour of experimental and numerical models is evaluated by monitoring the load-displacement and resulted deformation shapes. Results conclude that there is a slight increase in the load carrying capacity by adding longitudinal stiffeners that may encourage the use of such system for increasing the existing CFST columns.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Electrocoagulation For Oil and Grease Wastewater Treatment Using Iron Electrodes2112186634910.21608/erjm.2017.66349ENHisham K.El-EtribyProf. ,Public Works Depart., Faculty of Eng., Mansoura University.Kamal H.RadwanProf. ,Public Works Depart., Faculty of Eng., Mansoura University.KarimTahaCivil Eng., Graduated year 2012, Mansoura University.Journal Article20191225Batch electrocoagulation (EC) experiments were carried out to evaluate the removal of COD and O&G from wastewater using iron electrodes. The effects of operating parameters such as current intensity, initial COD concentration and contact time on COD and O&G removal efficiency had been investigated. It was found that increasing current intensity increased COD and O&G removal efficiency. Initial COD concentration had a little effect on removal efficiencies. Results showed that the COD removal efficiencies after 60 min. was 80.87 – 84.1 % at current of 1.3 A, 96.1 - 97.9 % at 1.6 A and after 45 min. was 97.9 - 98.6 % at 1.9 A. It can be noticed that after 60 min, for initial COD concentration of1280 mg/l the percentage COD removal was 83.13%, at 11.6 volt and 1.3 ampere, 97.5%, at 14 volt and 1.6 ampere and was 98.6 % at 16.4 volt and 1.9 ampere ,after 45 min .Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Hazard Degrees Assessment of Flash Floods, Applying Multi-Criteria Analysis, Gulf of Aqaba Basins, Sinai, Egypt2192366635010.21608/erjm.2017.66350ENM. M.AlyW.R. Management Lecturer, Faculty of Engineering, Matareya, Helwan Uni.
EgyptA. M. I. AbdElhamidResearcher, National Water Research Center, EgyptM. I.GadDesert Research Center, Cairo, EgyptJournal Article20191225Flash flood disasters have a significant impact and cause immense damages to lives and infrastructure. This study will assess the risk of flash floods in Gulf of Aqaba Basins (GAB), Sinai Peninsula. Watershed Modeling System (WMS) package was used to automatically delineate the drainage network and determine the hydro-morphological parameters of 33 GAB sub basins via the 90 m Digital Elevation Model files. These data were statistically analyzed applying Multi Criteria Analysis (MCA) technique to create flash flood hazard scale with and without outliers. Based on the resulted hazard scale MCA technique, it was found that 4% of the studied basins with high hazard degree (class five) while moderately high hazardous basins (class four) represent 32%. Class three contained 29% of the studied basins (moderate hazardous). While the moderately low hazardous basins (class two) contained 18% and the rest belongs to low hazardous degree. It is highly recommended to put into consideration this scale before investing in any flash flood protection projects in the study area.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Effect of Using Plastic Waste on Mechanical Properties of Concrete2372456635110.21608/erjm.2017.66351ENHaider K.AmmashAssist. Prof. Department of Civil Engineering, University of Al-Qadisiyah, IraqSadjad A.HemzahLecture Department of Civil Engineering, University of Al-Qadisiyah, Iraq.RashaJasimAssist. Lecture Department of Civil Engineering, University of Al-Qadisiyah, Iraq.Journal Article20191225The present study deals with the effect of using plastic waste on mechanical properties of concrete. The experimental work consists of adding manually formed serrated plastic fibers by ratios of (1%, 2% and 3%) of cement weight. Different lengths of fibers were used for each ratio with a constant width of 5 mm. It was noticed from laboratory tests that the addition of plastic fibers improves the compressive strength, tensile strength and modulus of rupture of concrete, by different ratios, about 20%, furthermore it could be a sufficient method to get rid of plastic waste.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701The Technology Application Aspect in Optimization of Islamic geometric patterns2572676635210.21608/erjm.2017.66352ENAya A.EL.TaweelTeaching assistant , Department of Architecture, Mansoura High Institute
of Engineering and Technology, Mansoura, EgypAliaa A.MahmoudTeaching assistant , Department of Architecture, Mansoura High
Institute of Engineering and Technology, Mansoura, EgyptJournal Article20191225For centuries, Islamic geometrical patterns (IGPs) were designed and built to respond effectively and dynamically to people’s physical, environmental, social, physiological and religious requirements at their time. The architects used to copy-paste various IGPs of the Islamic historical buildings in their design work without understanding the meanings and values that it holds. This way has often caused inappropriate use, regarding time-scale accuracy, architectural- style matching and even identity. In an attempt of handling this misunderstanding, there is a trend of combining technology applications in architecture to recruit IGPs design and maximize its purpose either function or decorative shape. For that, the research will analyze a number of buildings from different countries and cultures with IGPs applied in a technological way. The research proposes different technology techniques in dealing with IGPs in order to enhance the function and other purposes as possible as we can on a large scale.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701تقييم ما بعد الاستخدام لوظائف الفراغات العمرانية في المباني التعليمية بناءاً على خبرة المستخدمين2692806635310.21608/erjm.2017.66353ENسلوي مصطفيشحاتهکلية الهندسة-جامعة المنوفيةإسلام أحمدعبد القدوسمعهد الادارة العامة - الرياض- المملکة العربية السعوديةJournal Article20191225تمثل الفراغات العمرانية قلب الحرکة النابض بالکليات والجامعات، فبالإضافة لعملها کفراغات توزيع رئيسية، فهي حاضنة للأنشطة الطلابية، وتمثل نقاط التجمع والإلتقاء والإنتظار الرئيسية داخل حرم الکلية، وهي عنصر مکمل لوظيفة المنشآت الرئيسية، وتشير کفائتها الوظيفية والإجتماعية لمدى کفاءة المنشأ ککل في أداء وظيفته، وفي حالة وجود خلل في أداء هذه الفراغات لوظائفها فإن المستخدمين يقوموا بتهيئة هذه الفراغات بناء على خبرتهم الناتجة من التعامل اليومي معها، ويقوموا بخلق مجموعة من نقاط التجمع، او مجموعة من مسارات الحرکة غير المصممة مسبقا، بغرض تحقيق أفضل إستخدام لهذه الفراغات يمکن ان يوفر السرعة والکفاءة المنشودة.<br /> ويهدف البحث إلى فهم تأثير القرارات التخطيطية والتصميمة على مستخدمي الفراغات الموجودة في حرم کلية الهندسة جامعة المنوفية بناء على خبرة مستخدمي هذه الفراغات، من خلال قياس آراء المستخدمين ومدى رضاءهم وتفاعلهم مع الفراغات العمرانية في فصل الشتاء، لتحسين الأداء التخطيطي والتصميمي للفراغات والوصول الى بيئة عمرانية أفضل، إعتمادا على ثلاثة محاور في التحليل وهي (البعد المکاني والبعد البيئي والحرکي) لتحديد کفاءة الفراغات العمرانية في منطقة دراسة الحالة، للوصول لنتائج وتوصيات تهدف لرفع کفاءة الفراغات العمرانية وتحقق الاستدامة الوظيفية بمنطقة الدراسة، مما يساهم في رفع کفاءة الوسط العمراني ککل، من خلال منهج القياس الکمي في تحليل القياسات البيئية لعناصر التجمع الناشئة، وتحليل رأي المستخدمين.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701Impacts of Scour on Lateral Pile Behavior in the Marine Environment2812896635410.21608/erjm.2017.66354ENYasser El Sayed I.MostafaProfessor of Harbor Engineering and Marine Structures, Dept. of Irrigation & Hydraulics
Faculty of Engineering, Ain Shams University, Cairo, Egypt,Journal Article20191225Piles supporting marine structures are subjected to lateral loads due to berthing, mooring forces, waves and current forces. Scour around piles can have significant impact on the lateral loading capacity and hence affect the stability of marine structures. This paper presents the impact of scour on lateral loading of single piles and pile groups installed in coheshionless soils. Finite element modeling and Winkler model were used in the analyses. Different parameters were considered such as scour depth, magnitude of lateral load, pile group arrangement, pile spacing, pile slenderness ratio and pile batter angle. The results showed that global scour has greater impact on lateral pile capacity compared to local scour. Scour has greater impact on lateral loading of pile groups compared to its impact on single piles. Pile groups with side-by-side arrangement exposed to scour are more critical than single piles and piles groups with tandem arrangement due to the combined effect of scour and pile-soil-pile interaction. Some recommendations for scour protection are provided based on pile group arrangement, pile spacing and slenderness ratioMenoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701النسجيات الحائطية المستوحاة من فن التجهيز في الفراغ وأثرها علي التصميم الداخلي المعاصر2913006635510.21608/erjm.2017.66355ENجمعه حسينعبد الجوادأستاذ النسيج بکلية التربية النوعية -جامعة المنوفيةأيمن أحمد عفيفيالعربيأستاذ النسيج المساعد بکلية التربية النوعية -جامعة المنوفيةJournal Article20191225يعد فن التجهيز في الفراغ من الاتجاهات والتيارات الفنية التشکيليّة في الفن المعاصر (ما بعد الحداثة) ، حيث يقوم الفنان بإضافة مواد جاهزة بوضعها أو بتعليقها في الفراغ، ويستطيع المشاهد الدخول للمکان والتجول فيه کما لو کان جزءاً منه ، وقد واکب فن النسيج اليدوي الفنون الأخري في تأثرها بتيارات فنون ما بعد الحداثة وظهر ذلک في أعمال نسجية تجاوزت التقليدية في التقنية لاکتشاف طرق أدائية مستحدثة تخرج العمل النسجي من حدوده الضيقة ، والخروج عما هو متعارف عليه في هذا المجال فاتخذ العمل أشکال فنية متنوعة منها تحويل المسطح النسجي ذي البعدين إلي ثلاث أبعاد حقيقية وکذلک إلي مجسم کامل الاستدارة ، ومن خلال دراسة لخصائص اتجاهات فنون ما بعد الحداثة فإن البحث يتناول کيفية الاستفادة من فن التجهيز في الفراغ في صياغة نسجيات حائطية تجمع بين مجموعة من التقنيات و الأساليب المختلفة في عمل نسجي واحد وکذلک استخدام خامات غير تقليدية تحقق البعد الثالث الحقيقي في العمل النسجي و ذلک لإثراء التصميم الداخلي المعاصر.Menoufia University, Faculty of EngineeringERJ. Engineering Research Journal1110-118040320170701التعلم الإلکتروني المنتشر کأحد تطبيقات توظيف التکنولوجيا الهادئة2472566652710.21608/erjm.2017.66527ENمحمد زيدانعبد الحميداستاذ تکنولوجيا التعليم بکلية التربية النوعية - جامعة النتوفيةJournal Article20191226التکنولوجيا الهادئة هى حوسبة صغيره الحجم ومتکيفه مع المطالب وذکيه، وبنية التکنولوجيا الهادئه هى بنية تفاعليه تضبط وتتکيف مع مطالب الفرد الشخصية والاجتماعية والتغيرات البيئية حيث اطلق مارک وايزر mark Weiser، (1952-1999) من زيروکس، مصطلح التکنولوجيات الهادئه سنة 1991، ليصف ذلک العصر الذى ياتى بعد عصر الکمبيوتر العملاق، ثم المينى، ثم الشخصي، ثم الانترنت والحوسبه الموزعه، ثم النقال والمنتشر، للتغلب على هذا الکم الهائل من المعرفه المتضخمه، وفي سنة 1996 کتب مع جون سيلى براون(أبو التعلم المنتشر) وصول عصر التکنولوجيا الهادئه، وفيما يلي التعلم الإلکتروني المنتشر کأحد تطبيقات التکنولوجيا الهادئه:<br /> تعريف التعلم الإلکتروني المنتشر<br /> يعرف محمد خميس(2011، ص173) التعلم المنتشر بأنه "عملية تعلم سياقي حقيقي وظيفي وتکيفي، يتم من خلاله توصيل کائنات التعلم الإلکتروني المناسبة، إلى مجموعة من المتعلمين، متواجدين في أماکن مختلفة ومتباعدة، وإدارة عمليات التعلم والتفاعلات والأنشطة التعليمية الوظيفية المناسبة، في الوقت والمکان المناسبين، في فضاء الکتروني منتشر، باستخدام تکنولوجيات لاسلکية وأجهزة رقمية محمولة وممسوکة". ويؤکد أن التعلم المنتشر هو امتداد وتوسيع لمجال التعلم النقال، ولذلک فإن التعلم المنتشر يذهب بخطوات أبعد من التعلم النقال، فإذا کان التعلم النقال يرکز على تقديم التعلم في أي وقت ومکان، فإن التعلم المنتشر يرکز على تقديم التعلم المناسب، في الوقت المناسب، والمکان المناسب، باستخدام المصادر المناسبة.<br /> <br /> کما يعرفه "شاي" Shih (2012, p. 298) بأنه نموذج للتعلم يحدث في بيئة حاسوبية في کل مکان يمکن أي شخص من التعلم في المکان المناسب في الوقت المناسب ويستخدم الطالب العديد من الأجهزة التي تدعم التنقل والتي تمکنه من التعلم داخل وخارج بيئة التعلم التقليدية وفي مواقف تعلم فردية وجماعية، ومن هذه الأجهزة المساعد الرقمي الشخصي والکمبيوتر اللوحي والمحمول.